2630 THREE AND FIVE SECTION TANDEM DISKS
Three- and Five-Section Tandem Disks
- Perfect for light to medium soils, seedbed prep
- Features John Deere TruSet™ Tillage Technology
- Radial Tire Option
- Knife-edge Rolling Basket
- Extended-Life Bearing
Features
Ground-engaging components on 2633
Ground-engaging components on 2633
The John Deere 2630 Series offer three disk models that provide a wide range of variety for all tillage applications.
Model |
2630 Disk | 2633 Disk | 2635 Disk |
| Purpose | Secondary (light duty) | Dual purpose (medium duty) | Primary (heavy duty) |
| Working depth | Up to 130 mm (5 in.) | Up to 180 mm (7 in.) | Up to 200 mm (8 in.) |
| Weight per blade | Minimum 68 kg (150 lb) | Under 13.4 m (44 ft) Minimum 86 kg (190 lb) Over 13.4 m (44 ft) Minimum 91 kg (200 lb) |
Minimum 127 kg (280 lb) |
| Blade size | 560 or 610 mm (22 or 24 in.) |
610 or 660 mm (24 or 26 in.) |
610 or 660 mm (24 or 26 in.) |
| Blade spacing | 185 or 230 mm (7.25 or 9 in.) |
230 mm (9 in.) | 230 mm (9 in.) front and 280 mm (11 in.) rear, or 280 mm (11 in.) |
| Horsepower | 23 to 36 hp/m (7 to 11 hp/ft) | 23 to 36 hp/m (7 to 11 hp/ft) | 26 to 36 hp/m (8 to 11 hp/ft) |
| Working widths | 6.3 m to 15.0 m (20.75 ft to 49.25 ft) |
6.3 m to 15.0 m (20.75 ft to 49.25 ft) |
7.2 m to 12.4 m (23.58 to 40.66 ft) |
| Operating speed | 6.5 to 11.3 km/h (4 to 7 mph) |
6.5 to 11.3 km/h (4 to 7 mph) |
6.5 to 11.3 km/h (4 to 7 mph) |
| Recommended use |
|
|
|
John Deere's 2630 Series Disks offer different blade options for soil penetration and residue sizing.
Solid-spherical blade
Cutout-spherical blade
| Blade type | Solid-spherical blades | Cutout-spherical blades |
| Recommended application |
|
|
| Recommended soil type | Light to medium soils | Heavy to medium soils |
| Benefits | Better control of soil than cone blades since less sensitive to over speeding | Chopping or trapping residue |
| Penetration | Penetrate best at a 20-degree gang angle | Penetration is excellent with a cutout blade |
The 2630 General-Purpose Disk comes equipped with front and rear solid-spherical disk blades with 230-mm (9-in.) spacing. The primary blade size is 610 mm (24 in.) x 5 mm (0.197 in.)
230-mm (9-in.) blade spacing
230-mm (9-in.) spacing, front and rear
- Good for seedbed preparation and chemical incorporation in medium to heavy soils
- Works well in primary tillage in light to medium soils
- Provides good residue-handling capability
NOTE:
- The number 10 edge has a narrower profile than number 1 edge and should work well in most non-rock conditions.
- Rear main and wing gangs are tapered with one blade 51 mm (2 in.) smaller than the primary blade.
- Integral furrow filler blades are included with all rear wing gangs which are 102 mm (4 in.) smaller than the primary blade.
- Front outer gangs have a taper that is 51 mm (2 in.) smaller than the primary blade, except for 559-mm (22-in.) disk blades.
Number 10 edge (inside bevel, outside grind)
- Bevel
- Grind
51-mm (2-in.) disk gang bolts
Gang tension system
John Deere's 2630 Series Disks provide an innovative approach to tension disk gang bolts.
Residue management
As crop yields increase, so does the amount of residue after harvest. The John Deere 2630 Disk enables producers to prepare soil for planting.
Spring pack
Spring pack
John Deere’s mechanical wing control helps producers keep their frames level for five-section disks. Mechanical wing control is included in base equipment for all five-section 2630 Series Disks.
With this feature, a large spring is placed in the wing frame on each side of the disk. As the pivot point in the wing starts to raise, the spring presses against that point to keep the disk level through tough field conditions.
The red circles in the following image illustrate the area of the disk where the large spring is placed in the wing frame.
Mechanical wing control
John Deere mechanical wing control is an industry-exclusive feature. A five-section disk without mechanical wing control can show up to 75-mm (3-in.) of depth inconsistency across the wing frame.
John Deere 2630 Series Disks and Vertical Tillage Implements feature extended-life bearings. These more durable and reliable bearings allow producers to customize bearing maintenance for specific growing conditions and soil types.
The flange-mounted bearing and sealing system features improved contamination resistance. The advanced seal material is highly resistant to wear and damage caused by abrasive soils and other crop materials. The design of these is more durable and reliable than previous bearings.
The design of this bearing system allows for dynamic self-alignment to the gang bolt, as opposed to trunnion-mounted bearings that have limited alignment capability. This system features additional freedom of movement, accommodating a wider variety of field conditions. The bearing system has been designed to decrease stress and fatigue on the inner rolling surfaces, supporting extended bearing life.
The bearing and seal design allows for a limited, seasonal maintenance interval to minimize downtime. They also allow producers to customize the maintenance for specific growing conditions and soil types. The multi-lipped sealing system cannot be damaged by frequent greasing. It allows bearings to accept grease within the bearing as well as provide grease to the outer bearing surface to eliminate wear between the bearing and housing. With this design, the bearings can accept grease even if misaligned to the housing.
2630 Disk in the field
2630 Disk in the field
The 2630 Series Disks offer multiple upgrades and additional items as options versus the 2620 Series Disks to enhance the machine. Check out the following video to see more about the 2630 Series Disks.
Extended-life bearings
John Deere 2630 Series Disks and Vertical Tillage Implements feature extended-life bearings. These more durable and reliable bearings allow producers to customize bearing maintenance for specific growing conditions and soil type.
TruSet™ side-to-side feature
John Deere TruSet system is featured in base equipment for the 2630 Series Disks and Vertical Tillage Implements. TruSet side-to-side is also available and features individual section leveling.
Knife-edge hydraulic rolling basket
The hydraulic rolling basket is offered with a round bar or knife-edge. The knife-edge is best for heavier, wet soil, and can be used in rocky conditions.
Radial tires
The 2630 Series Disks and Vertical Tillage Implements feature radial tires for the mainframes in base equipment. Radial tires are available as an option on the wing frame and stabilizer wheels. These tires are designed to offer longer wear life and help minimize compaction with a wider plate and lower inflation pressures.
Stabilizer wheels
Producers can choose either mechanical stabilizer wheels or TruSet hydraulic stabilizer wheels as an option. Stabilizer wheels help to maintain a consistent, level depth and are recommended for operation on rolling ground. The mechanical stabilizer wheels can be manually adjusted with a turnbuckle. TruSet with side-to-side leveling capabilities also enables operators to control the TruSet hydraulic stabilizer wheels from the cab while on the go.
Specifications
| Key Specs | 2630-three-and-five-section-tandem-disks Current Model |
|---|---|
| Working width | 12.4 m 40.67 ft |
| Transport width | 4.95 m 16.25 ft |
| Transport height | 3.66 m 12 ft |
| Working depth | 7.6 to 12.7 cm 3 to 5 in. |
| Blade spacing | 18.4 cm 7.25 in. or 22.9 cm 9 in. |
| Horsepower per ft | 6.7 to 8.2 kW 9 to 11 hp |
| Operating speed | 8 to 11.3 km/h 5 to 7 mph |
| Machine | |
| Working width | 12.4 m 40.67 ft |
| Transport width | 4.95 m 16.25 ft |
| Transport height | 3.66 m 12 ft |
| Gang standards | C-spring |
| Gang angle | 21/19 degree (angle) |
| Purpose | Secondary |
| Working depth | 7.6 to 12.7 cm 3 to 5 in. |
| Weight per blade | 93.4 kg 206 lb |
| Blade size | 56 cm 22 in. or 61 cm 24 |
| Blade spacing | 18.4 cm 7.25 in. or 22.9 cm 9 in. |
| Horsepower per ft | 6.7 to 8.2 kW 9 to 11 hp |
| Operating speed | 8 to 11.3 km/h 5 to 7 mph |
| Blade concavity | |
| Blade thickness | |
| Number of blades | |
| Front blades | 68 with spacing of 18.4 cm 7.25 in. 56 with spacing of 22.9 cm 9 in. |
| Rear blades | 68 with spacing of 18.4 cm 7.25 in. 56 with spacing of 22.9 cm 9 in. |
| Total | 136 with spacing of 18.4 cm 7.25 in. 112 with spacing of 22.9 cm 9 in. |
| Number of C-Springs | |
| Main frame front | 6 with spacing of 18.4 cm 7.25 in. 6 with spacing of 22.9 cm 9 in. |
| Main frame rear | 4 with spacing of 18.4 cm 7.25 in. 4 with spacing of 22.9 cm 9 in. |
| 1st wing front | 6 with spacing of 18.4 cm 7.25 in. 6 with spacing of 22.9 cm 9 in. |
| 1st wing rear | 6 with spacing of 18.4 cm 7.25 in. 6 with spacing of 22.9 cm 9 in. |
| 2nd wing front | 6 with spacing of 18.4 cm 7.25 in. 6 with spacing of 22.9 cm 9 in. |
| 2nd wing rear | 6 with spacing of 18.4 cm 7.25 in. 6 with spacing of 22.9 cm 9 in. |
| Total | 34 with spacing of 18.4 cm 7.25 in. 34 with spacing of 22.9 cm 9 in. |
Accessories and Attachments
Depth Control System
Rolling Basket Valve - Manual Control - 04N1NBKK10660
Rolling Basket Valve - TruSet Control - 04N1NBKK10661
Adding the TruSet compatibility kit to the TruSet Tillage system enables operators of competitive tractors and older John Deere tractors to adjust their depth and pressure settings on the go from the cab.
With the TruSet compatibility kit, TruSet can be run on the following GreenStar™ system ready tractors:
- John Deere 20 Series Tractors and older
- Competitive tractors
Like the TruSet Tillage system, the compatibility kit will be available as a field-installed option that can be ordered with the 2630 Disks and Vertical Tillage or through aftermarket parts. The compatibility kit includes an implement add-on valve and installation components.
Components that make up the TruSet compatibility kit include:
- Implement add-on valve
- In-cab selective control valve (SCV) lever for control of TruSet via the implement add-on valve
- Controller to operate the implement add-on valve
- Harnesses to connect the system (controller/valve/SCV switch)
- Hoses to power the implement add-on valve from the tractor brackets and hardware
All model years of 2630 Disk, 2633 Disk, 2635 Disk, and 2633VT can be retrofitted with TruSet. The following chart identifies the components needed to equip TruSet on a 2630 Series Disk or VT with a GreenStar-ready tractor.
TruSet is compatible with John Deere and competitive tractors. Depending on the tractor, a compatibility kit may be needed in addition to the TruSet Tillage system. The following chart identifies the components needed to operate TruSet on a 2630 Disk, 2633 Disk, 2635 Disk, or 2633VT with a GreenStar-ready tractor.
| TruSet product | John Deere 30 Series and newer tractors | John Deere 20 Series Tractors (large frame or IVT™ system) | John Deere 20 Series Tractors (small frame or non IVT) | John Deere 10 Series Tractors and older | Competitive tractors |
| TruSet Tillage system | Yes | Yes | Yes | Yes | Yes |
NOTE: Software update may be required.
Reference the tractor and display compatibility page for additional information.
Integrated TruSet Tillage technology enables disk and vertical tillage operators to adjust disk depth and down pressure on the active hydraulic rolling baskets while on the go to respond to changing field conditions such as varying soils, heavier residue, and moisture.
With a short window of time to perform tillage operations, TruSet can provide significant productivity improvements as operators are able to adjust the implement while covering acres with the push of a button. By responding to conditions as they change throughout the field, TruSet enables operators to generate better-quality tillage performance with the first pass.
Using a GreenStar™ display, a user sees real-time data for disk depth and basket down pressure for assurance of desired tillage outcomes. Once the actual set point is validated and configured to the display in the cab, operators are able to make independent adjustments as small as 2.5 mm (0.10 in.). Four customizable presets enable operators to save and name different combinations of settings for their most common field conditions.
Single-point depth control is included with the TruSet Tillage system, giving operators the choice of automated or manual adjustments. Hydraulic routings on the 2630 Series Disks and Vertical Tillage are designed to allow each implement to feature both TruSet and standard single-point depth control for system redundancy, operator preference, and flexibility at resale.
Producers can upgrade to TruSet with side-to-side control to enable individual section leveling.
Components
TruSet is compatible with John Deere and competitive tractors. Depending on the tractor, a compatibility kit may be needed in addition to the TruSet Tillage system. The following chart identifies the components needed to operate TruSet on a 2630 Disk, 2633 Disk, 2625 Disk, or 2633VT with a GreenStar-ready tractor.
| TruSet product | John Deere 30 Series Tractors and newer | John Deere 20 Series Tractors (large frame or IVT™ system) | John Deere 20 Series Tractors (small frame or non IVT) | John Deere 10 Series Tractors and older | Competitive tractors |
| TruSet Tillage system | Yes | Yes | Yes | Yes | Yes |
The TruSet Tillage system will be available as a field-installed option that can be ordered with the field cultivator or through aftermarket parts.
All model years of the 2630, 2633, 2635, and 2633VT can be retrofitted with TruSet.
TruSet requires a GreenStar-ready tractor with a supported display and receiver. The TruSet Tillage system must have a connection to the tractor ISO connection.
Reference the tractor and display compatibility page for additional information.
Integrated TruSet Tillage technology enables disk and vertical tillage operators to adjust disk depth and down pressure on the active hydraulic rolling baskets while on the go to respond to changing field conditions such as varying soils, heavier residue, and moisture.
With a short window of time to perform tillage operations, TruSet can provide significant productivity improvements as operators are able to adjust the implement while covering acres with the push of a button. By responding to conditions as they change throughout the field, TruSet enables operators to generate better-quality tillage performance with the first pass.
Using a GreenStar™ display, a user sees real-time data for disk depth and basket down pressure for assurance of desired tillage outcomes. Once the actual set point is validated and configured to the display in the cab, operators are able to make independent adjustments as small as 2.5 mm (0.10 in.). Four customizable presets enable operators to save and name different combinations of settings for their most common field conditions.
Single-point depth control is included with the TruSet Tillage system, giving operators the choice of automated or manual adjustments. Hydraulic routings on the 2630 Series Disks and Vertical Tillage are designed to allow each implement to feature both TruSet and standard single-point depth control for system redundancy, operator preference, and flexibility at resale.
Producers can upgrade to TruSet with side-to-side control to enable individual section leveling.
Components
TruSet is compatible with John Deere and competitive tractors. Depending on the tractor, a compatibility kit may be needed in addition to the TruSet Tillage system. The following chart identifies the components needed to operate TruSet on a 2630 Disk, 2633 Disk, 2625 Disk, or 2633VT with a GreenStar-ready tractor.
| TruSet product | John Deere 30 Series Tractors and newer | John Deere 20 Series Tractors (large frame or IVT™ system) | John Deere 20 Series Tractors (small frame or non IVT) | John Deere 10 Series Tractors and older | Competitive tractors |
| TruSet Tillage system | Yes | Yes | Yes | Yes | Yes |
The TruSet Tillage system will be available as a field-installed option that can be ordered with the field cultivator or through aftermarket parts.
All model years of the 2630, 2633, 2635, and 2633VT can be retrofitted with TruSet.
TruSet requires a GreenStar-ready tractor with a supported display and receiver. The TruSet Tillage system must have a connection to the tractor ISO connection.
Reference the tractor and display compatibility page for additional information.
Hitch Links
Category IV Hitch Link Conversion Kit - 04N1NBN400586
Category V Hitch Link Conversion Kit - 04N1NBN400587
Hydraulic Wing Control
Hydraulic wing control
Hydraulic wing control is available as optional equipment on all 2630 Series Disk.
A John Deere-exclusive control valve allows varying hydraulic pressure to the wing-fold cylinders.
- Transfers weight from the mainframe to the wings to improve penetration in hard ground and/or heavy soils
- Increasing pressure to the rod end of the cylinder holds the wing level to prevent gouging in soft and/or moist soils
A pressure relief feature allows wings to flex over obstacles to help prevent damage to the cylinder rod.
Convenient knob adjustment can be easily reached from front of disk.
The indicator gauge provides the operator with a quick visual indication of the results of the adjustment.
Requires tractor with closed-center hydraulics or John Deere pressure and flow hydraulic system.
Requires operator to follow special operating instructions (see disk operator's manual).
Parking Stand
Scrapers
Combination scrapers
Convex scrapers
Combination scrapers come in base on all disks. Additional scrapers are available for use in high residue conditions where plugging occurs on the spools. Use order code 9206 or 9208.
For use in wet, sticky soils where buildup occurs on the convex side of the disk blade, use order code 9209.
NOTE: Do not use scrapers at bearing standard locations.
Spool knockout scrapers
C-spring knockout scrapers
For number of blades and C-springs by size and spacing, see Specifications for 2630 Series Disks.
Combination scrapers
Convex scrapers
Combination scrapers come in base on all disks. Additional scrapers are available for use in high residue conditions where plugging occurs on the spools. Use order code 9206 or 9208.
For use in wet, sticky soils where buildup occurs on the convex side of the disk blade, use order code 9209.
NOTE: Do not use scrapers at bearing standard locations.
Spool knockout scrapers
C-spring knockout scrapers
For number of blades and C-springs by size and spacing, see Specifications for 2630 Series Disks.
Combination scrapers
Convex scrapers
Combination scrapers come in base on all disks. Additional scrapers are available for use in high residue conditions where plugging occurs on the spools. Use order code 9206 or 9208.
For use in wet, sticky soils where buildup occurs on the convex side of the disk blade, use order code 9209.
NOTE: Do not use scrapers at bearing standard locations.
Spool knockout scrapers
C-spring knockout scrapers
For number of blades and C-springs by size and spacing, see Specifications for 2630 Series Disks.
Combination scrapers
Convex scrapers
Combination scrapers come in base on all disks. Additional scrapers are available for use in high residue conditions where plugging occurs on the spools. Use order code 9206 or 9208.
For use in wet, sticky soils where buildup occurs on the convex side of the disk blade, use order code 9209.
NOTE: Do not use scrapers at bearing standard locations.
Spool knockout scrapers
C-spring knockout scrapers
For number of blades and C-springs by size and spacing, see Specifications for 2630 Series Disks.